ee91d5f9a6
This should match the Vial representation exactly (which also ignores stagger and splay).
65 lines
4.2 KiB
Markdown
65 lines
4.2 KiB
Markdown
# Tutte Coxeter 36k
|
|
|
|
|
|
|
|
This is firmware for a Raspberry Pi Pico PR2040 controller monoblock 36 key design
|
|
(split 3x5_3 - three rows of five, and three thumb keys, for each hand). This is a
|
|
*diode-free* design with a sparse 13 by 13 scanning matrix designed using a partial
|
|
[Tutte-Coxeter](https://en.wikipedia.org/wiki/Tutte%E2%80%93Coxeter_graph) graph
|
|
(using only 26 vertices or GPIO pins, with 36 edges or keys - see this
|
|
[blog post](https://astrobeano.blogspot.com/2025/05/ergo-mech-keyboard-wiring-using-tutte-coxeter-graph.html)
|
|
for background, although the final pin selection and trace routing changed):
|
|
|
|
| | GP11 | GP10 | GP3 | GP4 | GP7 | GP26 | GP27 | GP28 | GP15 | GP21 | GP19 | GP20 | GP16 |
|
|
|------|------|------|-----|-----|-----|------|------|------|------|------|------|------|------|
|
|
| GP12 | Z | | | | | | J | | | | | | |
|
|
| GP8 | Q | S | | | | | | | | | | ; | |
|
|
| GP9 | | X | C | | | | | | | | | | |
|
|
| GP1 | | | D | R | | | | | | O | | | |
|
|
| GP6 | | | | V | G | | | | | | | | |
|
|
| GP2 | | W | | | T | Y | | | | | | | |
|
|
| GP22 | | | | | | H | M | | | | | | R3 |
|
|
| GP0 | | | E | | | | U | I | | | | | |
|
|
| GP13 | | | | | B | | | K | L2 | | | | |
|
|
| GP14 | A | | | | | | | | L1 | L | | | |
|
|
| GP18 | | | | | | N | | | | . | R2 | | |
|
|
| GP17 | | | | | | | | , | | | R1 | / | |
|
|
| GP5 | | | | F | | | | | | | | P | L3 |
|
|
|
|
The keys here are labeled as per Qwerty, with L1, L2, L3, R3, R2, and R1 for the thumbs:
|
|
|
|
| Q | W | E | R | T | | Y | I | O | U | P |
|
|
|:-:|:-:|:--:|:--:|:--:|:-:|:--:|:--:|:--:|:-:|:-:|
|
|
| A | S | D | F | G | | H | J | K | L | ; |
|
|
| Z | X | C | V | B | | N | M | , | . | / |
|
|
| | | L1 | L2 | L3 | | R3 | R2 | R1 | | |
|
|
|
|
The firmware follows the `LAYOUT_split_3x5_3` QMK community layout convention, making it much
|
|
easier to use with an existing layout like Miryoku.
|
|
|
|
The first physical PCB for this was designed using the [Gamma Omega
|
|
keyboard](https://github.com/unspecworks/gamma-omega) footprint from Ergogen.
|
|
This is intend use the same Raspberry Pi Pico YD-RP2040 microcontroller board
|
|
to fit the same 3D printed case, including reset button placement.
|
|
|
|
* Keyboard Maintainer: [Peter J. A. Cock](https://github.com/peterjc)
|
|
* Hardware Supported: Tutte Coxeter 36k (single PCB) with Raspberry Pi Pico
|
|
* Hardware Availability: https://github.com/unspecworks/gamma-omega/tree/main/tc36k
|
|
|
|
Make example for this keyboard (after setting up your build environment):
|
|
|
|
make tutte_coxeter_36k:default
|
|
|
|
Flashing example for this keyboard:
|
|
|
|
make tutte_coxetter_36k:default:flash
|
|
|
|
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
|
|
|
|
## Bootloader
|
|
|
|
Enter the bootloader in 3 ways:
|
|
|
|
* **Bootmagic reset**: Hold down the key at (0,0) in the matrix (bottom left key, Qwerty `z`) and plug in the keyboard
|
|
* **Physical reset button**: Briefly press the button on the back of the controller (if physically accessible)
|
|
* **Keycode in layout**: Press the key mapped to `QK_BOOT` if it is available
|